WALL MOUNTY BIT SET INSTALL
WALL MOUNTY BIT SET PLUS
WALL MOUNTY BIT SET SERIES
WALL MOUNTY BIT SET TV

If you’re handy, it’s really not too hard to wall-mount a TV, but not everyone has the DIY skills, or inclination, to take on the job. Measure out 3/4 of an inch to find the center of the studs, and then use 16-inch increments to find the other studs nearest the TV’s mounting location. You can also look for a light switch or power outlet, since these are mounted on the side of a stud.

WALL MOUNTY BIT SET PLUS

Then, use an upright straightedge or yardstick, plus a vertical level, to mark a location higher on the wall. You might be able to find these small holes by feeling for dimples-though they may be spackled and painted-or by running a magnet across the surface to locate the nails. Wall trim or baseboards are usually nailed to the studs. Sheetrock is usually attached to studs using either screws or nails, so using a strong magnet to find a screw or nail head should put you near the center of that stud. Start at a corner of a room and then measure along the wall in 16-inch increments to locate the most likely location of the studs for your installation.

WALL MOUNTY BIT SET SERIES

(With any of these, confirm the position of each stud by drilling a series of small holes to locate the edges of the studs.) Most walls are constructed with the studs installed with the center of each 16 inches away from the next one. If you don’t have a stud finder, there are a few other carpenter’s tricks to locating a wall stud. For the most secure attachment, the bolt should be firmly centered in any stud you are using. Next, move on to the start and end of the next stud, marking the positions as you move along. Then move it horizontally at the same height to locate the end of the first stud. When it does, mark that with a pencil or some painter’s tape so you remember the position.

WALL MOUNTY BIT SET TV

Move your stud finder across the wall at the height you will be installing the TV mount until it indicates it has found the edge of a stud.

The easiest way to do this is by using a stud finder. You’ll want to screw the TV mount into wall studs (or into masonry using the appropriate anchors) for the most secure installation. You should make sure the location gives you easy access to an electrical outlet for power, and that you’ll have adequate storage for any components, such as a cable box, streaming player, or game console, you’ll be connecting to the TV.

WALL MOUNTY BIT SET INSTALL

If you need to install the TV higher, you’ll want to consider a tilting or articulating mount (see below). Instead, try to hang the TV so the bottom of the screen is no higher than eye level when you’re seated, and the top of the screen no higher than eye-level when you’re standing. But a wall-mounted TV tends to look weird when installed that low. If you were placing your TV on a stand, you’d want the center of the screen to be at eye level when you were seated. The height of the screen, and the angle from the screen to where you’ll be sitting, affects picture quality. Installing a TV on brick, block, or plaster walls generally requires special tools and hardware if it’s not included with the mount. You’ll want to attach the mount to framing studs-and not just drywall-to make sure it will support the weight of the TV.

You can try a few different positions using painter’s tape to mark off the TV’s dimensions on the wall.

All Rights Reserved.ĭistributed by Walmart Inc.Decide where you want to hang your TV before you go shopping for a mount, because that will affect the type of hardware you choose. Do not install this product on the ceiling. Do not install into a wood stud.ĬAUTION: This product can only be installed on a perpendicular wall. STEP 2 B Concrete, Stone or Masonry InstallationĬAUTION: The concrete wall minimum thickness is 5.5′, and surface covering can’t be more than 3/8″.ĬAUTION: These anchors are for concrete, stone or masonry wall ONLY. NEVER USE ANCHOR F FOR WOOD STUD ASSEMBLYĬAUTION: The wood stud minimum size is 2×4″, and surface covering can’t be more than 5/81 Drill hole on the wood stud centerline. Discard all unused hardware after you have completed TV mount installation.įor wood stud installation, follow STEP 2Aįor concrete wall installation, follow STEP 2B STEP 2 A Wood Stud Installation You will have screws, spacers and washers leftover. Use spacers and washers as needed since they are not always required. CAUTION: Carefully lay your TV on its face on a flat, non-abrasive surface covered with a blanket or soft padding to help prevent damaging the screen.ĬAUTION: Place left and right TV bracket in the appropriate position, make sure they are CENTERED on the back of TV and LEVEL with one another.Ĭhoose proper screws that fit your particular TV mounting holes.

Wall mounty bit set